Worked case · Electrical

Generator Inlet: 30 A or 50 A, and What Size Wire?

Winter storm season is when power inlet boxes and interlock kits sell out. Before you buy one, work out what your generator can actually push through it and what wire the run back to the panel needs. Here is the full calculation for a 7,500 W generator and a panel 40 feet away.

A lightning bolt in the evening sky above a house
Storms are when a portable generator earns its keep, but only if the inlet, the interlock and the wire back to the panel were sized before the lights went out. Photo: Nikolett Emmert / Unsplash

The case: a homeowner bought a portable generator rated 7,500 running watts and 9,500 starting watts, with both a 30 A twist-lock receptacle (L14-30R) and a 50 A receptacle. They want a power inlet box on the outside wall of the garage and a listed interlock kit on the main panel, which sits about 40 ft of cable run away. Should the inlet be 30 A or 50 A, and what wire goes between the inlet and the panel?

Short answer: for this generator a 30 A inlet, a 30 A two-pole breaker under the interlock and 10 AWG copper are enough. That path carries up to 7,200 W, which is 96% of the generator's running rating, with 1.21% voltage drop over 40 ft. A 50 A inlet would only unlock another 300 W. It pays off with a larger generator, not with this one.

1. Start from the generator's receptacle, not its brochure

The number on the box, 7,500 W, is the generator's continuous output. At 240 V that is:

7,500 W ÷ 240 V = 31.25 A

But the power never leaves the generator as an abstract number. It leaves through a receptacle, and each receptacle has its own rating and its own breaker on the generator panel. A 30 A, 4-wire L14-30 connection can deliver at most:

30 A × 240 V = 7,200 W

A 50 A, 4-wire connection raises that ceiling to 12,000 W. So the first rule of sizing an inlet is simple: the inlet can never be bigger than the largest 240 V receptacle on your generator, and there is no point in making it much bigger than the generator's running output.

For this case, 31.25 A sits just above 30 A. The 30 A path leaves 300 W on the table, about the draw of a few LED lights and a phone charger. That is the whole argument for 50 A here, and it is a weak one.

2. Remember that 240 V power comes in two halves

A 4-wire generator connection gives you two 120 V legs plus a neutral and a ground. Most of what you run in an outage, such as the refrigerator, the furnace blower, the sump pump, lights and the internet router, is 120 V and lands on one leg or the other. Each leg is limited separately:

  • 30 A inlet: 3,600 W per leg
  • 50 A inlet: 6,000 W per leg

If every 120 V load you care about is on the same leg, you can trip the generator at 3,600 W while the meter shows half the capacity unused. Before the outage, look at your panel and note which essential circuits sit on which leg. Spreading them out is free and often helps more than a bigger inlet.

Generator running7,500 WVia 30 A inlet7,200 WVia 50 A inlet7,500 WOne leg, 30 A3,600 W
Figure 1. What reaches the house from a 7,500 W generator: the 30 A path delivers 96% of the running rating, but each 120 V leg is capped at 3,600 W.

3. Size the breaker under the interlock

An interlock kit is a sliding plate that makes it physically impossible to turn on the generator breaker while the utility main is on. The generator breaker is a normal two-pole breaker that is fed backward from the inlet. Two rules apply:

  • Its rating must not exceed the inlet's rating. A 30 A inlet gets a 30 A two-pole breaker; a 50 A inlet gets a 50 A breaker, or a smaller one if your generator's 50 A receptacle is protected at less.
  • Because it is backfed, the NEC requires it to be secured in place with an additional fastener (408.36(D)). Most interlock kits include a hold-down bracket for this.

The NEC also requires transfer equipment for any connection of a generator to premises wiring, so that the utility and the generator can never be connected together (702.5). Use an interlock that is listed for your exact panel model; a homemade plate does not qualify.

4. Choose the wire between inlet and panel

The conductors must be protected by the breaker under the interlock, so you size them to that breaker:

  • 30 A: 10 AWG copper. In NM-B cable, 10 AWG is good for exactly 30 A at the 60 °C rating, so 10/3 with ground works indoors.
  • 50 A: 8 AWG copper THHN/THWN-2 in conduit at the 75 °C rating. In NM-B, 8 AWG is only good for 40 A, so a 50 A run in cable needs 6 AWG.

You need four conductors either way: two hots, a neutral and an equipment ground. The neutral is not optional, because almost all of your outage loads are 120 V.

Main panel30 A 2-pole, interlocked10 AWG Cu40 ftPower inletL14-30120/240 VVoltage drop 1.21%
Figure 2. The case: a 30 A inlet on the garage wall, 40 ft of 10 AWG copper and a 30 A interlocked breaker in the main panel.

5. Check voltage drop, including the cord

Over a short run, voltage drop is rarely the issue. It becomes one when the panel is on the far side of the house or the inlet is on a detached garage.

One-way run 30 A inlet: wire Drop 50 A inlet: wire Drop
25 ft 10 AWG 0.76% 8 AWG 0.80%
40 ft 10 AWG 1.21% 8 AWG 1.27%
75 ft 10 AWG 2.27% 8 AWG 2.39%
100 ft 8 AWG 1.91% 6 AWG 2.05%
150 ft 8 AWG 2.87% 4 AWG 1.93%

The table assumes the inlet runs at its full rating, which is the worst case. Don't forget the cord between the generator and the inlet. A 25 ft, 10-gauge cord at 30 A adds about 1.9 V, or 0.78% (using 1.24 Ω per 1,000 ft for stranded 10 AWG copper from NEC Chapter 9, Table 8). Cord plus house wiring in this case comes to 1.99%, comfortably inside the usual 3% target.

0.01.63.24.86.48.004080120160200One-way length (ft)Drop (%)40 ft10 AWG8 AWG3% target6 AWG
Figure 3. Voltage drop at 30 A and 240 V by copper wire size and distance between the inlet and the panel.
A row of gray electric meters on an outside wall
Figure 4. The meter is where the utility's lines meet yours. A listed interlock keeps generator power from flowing back past it toward line crews and neighbors. Photo: Tim Mossholder / Unsplash

6. Which inlet for which generator

Same 40 ft run, copper, inlet loaded to its rating:

Generator, running watts Current at 240 V Usable via 30 A Usable via 50 A Sensible inlet
5,000 W 20.8 A 5,000 W 5,000 W 30 A
7,500 W 31.3 A 7,200 W 7,500 W 30 A
9,500 W 39.6 A 7,200 W 9,500 W 50 A
12,000 W 50.0 A 7,200 W 12,000 W 50 A

At 9,500 running watts the 30 A path would waste 2,300 W, which is when 50 A starts to make sense, as long as the generator has a 50 A receptacle. A generator with only 120 V receptacles cannot feed a 4-wire inlet at all; never jumper the two legs together to make it fit.

0.01.63.24.86.48.004080120160200One-way length (ft)Drop (%)40 ft8 AWG6 AWG3% target4 AWG
Figure 5. The same check for a 50 A inlet: voltage drop at 50 A and 240 V by copper wire size.

How to read the generator panel and the inlet label

  • Running (rated) watts and starting (surge) watts. Size everything from running watts; surge only lasts seconds.
  • Receptacle types and their breakers. The L14-30R is protected at 30 A. A 50 A receptacle may be protected at less on some models; the breaker printed on the panel is what counts.
  • Neutral bonding. The manual says whether the neutral is bonded to the frame. With an interlock the neutral is not switched, so many manufacturers and inspectors expect a floating-neutral connection. Follow the generator manual and your inspector here.
  • Inlet rating and wire range. Inlets list their amperage, voltage (125/250 V) and the wire sizes their terminals accept. One 50 A inlet we checked accepts copper from 8 AWG to 6 AWG only.

Installation checklist

  • Interlock kit listed for your panel brand and model, with the generator breaker in the position the kit requires.
  • Two-pole backfed breaker no larger than the inlet rating, held down with the kit's fastener.
  • Four-conductor run: 10 AWG copper for 30 A, sized to the breaker.
  • Inlet box rated for outdoor (wet) locations, mounted where the generator can sit well away from doors, windows and vents.
  • Cord matched to the inlet: 30 A with 10-gauge conductors, or a 50 A cord for a 50 A inlet.
  • Labels on the panel and inlet, a working carbon monoxide alarm on every level, and a permit and inspection where your jurisdiction requires them.

Signs of a problem

  • Generator breaker trips on one leg only: loads are unbalanced; move a big 120 V load to the other leg.
  • Lights dim when the well pump or furnace starts: expected for a moment; if they stay dim, check the cord gauge and the terminations.
  • Warm inlet or cord plug: a loose or corroded pin. Shut down and inspect before the next use.
  • GFCI on the generator trips as soon as it connects: often a neutral-bonding conflict between the generator and the panel.

Common mistakes

  • Buying a 50 A inlet for a generator that only has a 30 A twist-lock. You will never get more than 7,200 W through it.
  • A 50 A breaker on 10 AWG wire. The wire must match the breaker, not the inlet.
  • A "suicide cord" into a dryer or wall outlet. The Consumer Product Safety Commission warns that this backfeed can electrocute utility workers and neighbors and bypasses your home's protection.
  • Forgetting the leg balance and blaming the generator.
  • Running the generator in the garage "with the door open." Carbon monoxide does not care about the door.

FAQ

Is a 30 amp inlet enough for a 7,500 watt generator? Yes, for practical purposes. A 30 A, 240 V inlet carries 7,200 W, which is 96% of 7,500 W.

What size wire for a 30 amp generator inlet? 10 AWG copper with four conductors. At 40 ft the drop is 1.21%; at 150 ft you would want 8 AWG (2.87%).

What size wire for a 50 amp generator inlet? 8 AWG copper in conduit at 40 ft, or 6 AWG in NM-B cable. At 150 ft the calculator gives 4 AWG.

How much can one leg carry? 3,600 W on a 30 A inlet and 6,000 W on a 50 A inlet, at 120 V.

Does a long cord matter? A 25 ft, 10-gauge cord at 30 A drops about 1.9 V (0.78%). Doubling the length doubles the drop.

Summary

Item 7,500 W generator, 40 ft to panel
Generator current at 240 V 31.25 A
Inlet 30 A, 4-wire (L14-30)
Breaker under the interlock 30 A two-pole, held down
Wire, inlet to panel 10 AWG copper
Voltage drop, house run 1.21%
Voltage drop with 25 ft cord 1.99%
Maximum through the inlet 7,200 W (3,600 W per leg)

Have a different generator, inlet or distance? Run it through the SizeBench wire size calculator and get the wire gauge and voltage drop in one step.

Try it with your own numbersWire Size Calculator→

Sources and references

  1. NFPA 70, National Electrical Code (NEC) 702.5 (transfer equipment for optional standby systems), 408.36(D) (backfed breakers secured by an additional fastener), 240.4(D) and Table 310.16 (ampacity, 60 °C limit for NM-B), Chapter 9 Table 8 (conductor resistance for cord voltage drop)
  2. U.S. Consumer Product Safety Commission – Portable Generator Safety Alert never backfeed through a wall outlet (danger to utility workers and neighbors); run generators outside, far from windows, doors and vents
  3. Reliance Controls – PBN50 50 A power inlet box, installation sheet example of inlet wiring limits (copper 8 AWG to 6 AWG), four-wire connection, requirement to use a transfer switch, CO placement warning
  4. SizeBench wire size calculator wire gauge and voltage drop for 30 A and 50 A at 240 V by distance

Standards and data behind our calculators

How we made this guide

Every number in this guide is calculated by the same code as our calculators, from the standards listed above, and the page is tested before publication. Redação Grupo TAAP wrote it; we use automation and AI tools to help draft, never to produce the figures. Thiago André Azevedo Pires, managing editor, reviewed and approved it before publication. Methodology and sources →

Revision history

  • · Published
  • · Reviewed