How to size a wire
A wire must pass two separate checks. First, its ampacity (how much current it can carry without overheating) must be at least the load current, or 125% of it for continuous loads. Second, the voltage drop over the run should stay under about 3% so motors, chargers and lights get enough voltage. On short runs ampacity decides the size; on long runs voltage drop usually does.
Formula
Example: 40 A at 240 V, 150 ft, copper
8 AWG copper is rated 50 A, so it passes ampacity. Its voltage drop is 2 × 150 × 40 × 0.764 ÷ 1000 = 9.2 V, or 3.8%, which is too high. 6 AWG gives 5.9 V (2.5%), so 6 AWG is the answer.
Wire size chart (NEC 310.16, 75°C)
| Size | Copper | Aluminum | Typical use |
|---|---|---|---|
| 14 AWG | 15 A* | – | Lighting circuits |
| 12 AWG | 20 A* | 15 A* | Receptacles, kitchen |
| 10 AWG | 30 A* | 25 A* | Water heater, dryer, A/C |
| 8 AWG | 50 A | 40 A | Range, small subpanel |
| 6 AWG | 65 A | 50 A | EV charger, subpanel |
| 4 AWG | 85 A | 65 A | Subpanel feeder |
| 2 AWG | 115 A | 90 A | 90 A feeder |
| 1/0 AWG | 150 A | 120 A | Feeders |
| 2/0 AWG | 175 A | 135 A | Feeders |
| 4/0 AWG | 230 A | 180 A | 200 A service (Al, per 310.12) |
* Limited by NEC 240.4(D) small-conductor overcurrent rules.
AWG wire gauge chart: 4/0 to 40 AWG
Diameter, cross-section and copper resistance for every American Wire Gauge size from 0000 down to 40, computed from the exact AWG definition.
Show full table
| AWG | Diameter (in) | Diameter (mm) | Area (kcmil) | Area (mm²) | Cu Ω/1000 ft | Cu Ω/km | Nearest metric |
|---|---|---|---|---|---|---|---|
| 4/0 (0000) | 0.4600 | 11.68 | 211.6 | 107.2 | 0.04901 | 0.1608 | 120 mm² |
| 3/0 (000) | 0.4096 | 10.40 | 167.8 | 85.03 | 0.06180 | 0.2028 | 95 mm² |
| 2/0 (00) | 0.3648 | 9.266 | 133.1 | 67.43 | 0.07793 | 0.2557 | 70 mm² |
| 1/0 (0) | 0.3249 | 8.251 | 105.5 | 53.48 | 0.09827 | 0.3224 | 50 mm² |
| 1 | 0.2893 | 7.348 | 83.69 | 42.41 | 0.1239 | 0.4066 | 50 mm² |
| 2 | 0.2576 | 6.544 | 66.37 | 33.63 | 0.1563 | 0.5127 | 35 mm² |
| 3 | 0.2294 | 5.827 | 52.63 | 26.67 | 0.1970 | 0.6464 | 25 mm² |
| 4 | 0.2043 | 5.189 | 41.74 | 21.15 | 0.2485 | 0.8152 | 25 mm² |
| 5 | 0.1819 | 4.621 | 33.10 | 16.77 | 0.3133 | 1.028 | 16 mm² |
| 6 | 0.1620 | 4.115 | 26.25 | 13.30 | 0.3951 | 1.296 | 16 mm² |
| 7 | 0.1443 | 3.665 | 20.82 | 10.55 | 0.4982 | 1.634 | 10 mm² |
| 8 | 0.1285 | 3.264 | 16.51 | 8.366 | 0.6282 | 2.061 | 10 mm² |
| 9 | 0.1144 | 2.906 | 13.09 | 6.634 | 0.7921 | 2.599 | 6 mm² |
| 10 | 0.1019 | 2.588 | 10.38 | 5.261 | 0.9988 | 3.277 | 6 mm² |
| 11 | 0.09074 | 2.305 | 8.234 | 4.172 | 1.260 | 4.132 | 4 mm² |
| 12 | 0.08081 | 2.053 | 6.530 | 3.309 | 1.588 | 5.211 | 4 mm² |
| 13 | 0.07196 | 1.828 | 5.178 | 2.624 | 2.003 | 6.571 | 2.5 mm² |
| 14 | 0.06408 | 1.628 | 4.107 | 2.081 | 2.525 | 8.285 | 2.5 mm² |
| 15 | 0.05707 | 1.450 | 3.257 | 1.650 | 3.184 | 10.45 | 1.5 mm² |
| 16 | 0.05082 | 1.291 | 2.583 | 1.309 | 4.015 | 13.17 | 1.5 mm² |
| 17 | 0.04526 | 1.150 | 2.048 | 1.038 | 5.063 | 16.61 | 1 mm² |
| 18 | 0.04030 | 1.024 | 1.624 | 0.8230 | 6.385 | 20.95 | 0.75 mm² |
| 19 | 0.03589 | 0.9116 | 1.288 | 0.6527 | 8.051 | 26.41 | 0.75 mm² |
| 20 | 0.03196 | 0.8118 | 1.022 | 0.5176 | 10.15 | 33.31 | 0.5 mm² |
| 21 | 0.02846 | 0.7229 | 0.8101 | 0.4105 | 12.80 | 42.00 | 0.5 mm² |
| 22 | 0.02535 | 0.6438 | 0.6424 | 0.3255 | 16.14 | 52.96 | – |
| 23 | 0.02257 | 0.5733 | 0.5095 | 0.2582 | 20.36 | 66.78 | – |
| 24 | 0.02010 | 0.5106 | 0.4040 | 0.2047 | 25.67 | 84.21 | – |
| 25 | 0.01790 | 0.4547 | 0.3204 | 0.1624 | 32.37 | 106.2 | – |
| 26 | 0.01594 | 0.4049 | 0.2541 | 0.1288 | 40.81 | 133.9 | – |
| 27 | 0.01420 | 0.3606 | 0.2015 | 0.1021 | 51.47 | 168.9 | – |
| 28 | 0.01264 | 0.3211 | 0.1598 | 0.08098 | 64.90 | 212.9 | – |
| 29 | 0.01126 | 0.2859 | 0.1267 | 0.06422 | 81.83 | 268.5 | – |
| 30 | 0.01003 | 0.2546 | 0.1005 | 0.05093 | 103.2 | 338.5 | – |
| 31 | 0.008928 | 0.2268 | 0.07970 | 0.04039 | 130.1 | 426.9 | – |
| 32 | 0.007950 | 0.2019 | 0.06321 | 0.03203 | 164.1 | 538.3 | – |
| 33 | 0.007080 | 0.1798 | 0.05013 | 0.02540 | 206.9 | 678.8 | – |
| 34 | 0.006305 | 0.1601 | 0.03975 | 0.02014 | 260.9 | 856.0 | – |
| 35 | 0.005615 | 0.1426 | 0.03152 | 0.01597 | 329.0 | 1,079 | – |
| 36 | 0.005000 | 0.1270 | 0.02500 | 0.01267 | 414.8 | 1,361 | – |
| 37 | 0.004453 | 0.1131 | 0.01983 | 0.01005 | 523.1 | 1,716 | – |
| 38 | 0.003965 | 0.1007 | 0.01572 | 0.007967 | 659.6 | 2,164 | – |
| 39 | 0.003531 | 0.08969 | 0.01247 | 0.006318 | 831.8 | 2,729 | – |
| 40 | 0.003145 | 0.07987 | 0.009888 | 0.005010 | 1,049 | 3,441 | – |
Solid annealed copper at 20 °C (ρ = 1.7241 × 10⁻⁸ Ω·m, 100 % IACS). d = 0.005 in × 92(36 − n)/39; 0000 = n −3. Stranded wire is about 2–3 % larger in diameter and slightly higher in resistance (NEC Chapter 9, Table 8). Nearest metric = closest IEC size by area (within ±30 %), not an equivalent ampacity.
Copper wire ampacity: NEC Table 310.16 (60 / 75 / 90 °C)
Allowable ampacity of insulated copper conductors, not more than three current-carrying conductors in a raceway, cable or earth, 30 °C (86 °F) ambient.
Show full table
| AWG | 60 °C (TW, UF, NM-B) | 75 °C (THWN, XHHW) | 90 °C (THHN, XHHW-2) | Max. breaker (240.4(D)) | Area (mm²) |
|---|---|---|---|---|---|
| 14 | 15 A* | 20 A* | 25 A* | 15 A | 2.08 |
| 12 | 20 A* | 25 A* | 30 A* | 20 A | 3.31 |
| 10 | 30 A* | 35 A* | 40 A* | 30 A | 5.26 |
| 8 | 40 A | 50 A | 55 A | – | 8.37 |
| 6 | 55 A | 65 A | 75 A | – | 13.3 |
| 4 | 70 A | 85 A | 95 A | – | 21.2 |
| 3 | 85 A | 100 A | 115 A | – | 26.7 |
| 2 | 95 A | 115 A | 130 A | – | 33.6 |
| 1 | 110 A | 130 A | 145 A | – | 42.4 |
| 1/0 | 125 A | 150 A | 170 A | – | 53.5 |
| 2/0 | 145 A | 175 A | 195 A | – | 67.4 |
| 3/0 | 165 A | 200 A | 225 A | – | 85.0 |
| 4/0 | 195 A | 230 A | 260 A | – | 107.0 |
Table values from NEC 2023 Table 310.16. * 14, 12 and 10 AWG copper are limited to 15, 20 and 30 A overcurrent protection by NEC 240.4(D) regardless of insulation. Use the 90 °C column only for derating; the final ampacity may not exceed the terminal rating (usually 60 °C up to 100 A, 75 °C above, NEC 110.14(C)). NM-B cable is always sized at 60 °C.
Frequently asked questions
What size wire do I need for 50 amps?
6 AWG copper (65 A at 75°C) is the usual choice for a 50 A circuit such as an EV charger or range. Long runs may need 4 AWG to keep voltage drop under 3%.
What size wire for a 100 amp subpanel?
Typically 3 AWG copper or 1 AWG aluminum at 75°C. Runs over about 100 ft often need one size larger for voltage drop.
How far can I run 12 gauge wire on a 20 amp circuit?
At 120 V and a full 16 A continuous load, 12 AWG copper stays under 3% drop up to about 58 ft one way. At lighter loads it can go farther.
Is aluminum wire safe?
Modern AA-8000 aluminum feeders are code-approved and common for services and feeders. Use connectors rated AL/CU and an anti-oxidant compound.